VW Bug - MR2 Create masonite template for cutting frame plates #45

Posted on February 14th, 2009 by Tim in VW Beetle Turbo Build
Using the VW Bug foam frame templates I constructed a masonite template to use as a guide for the plasma torch. I made this template .125 inches smaller that the actual foam template because of the plasma cutter’s tip. The template insures that I have an accurate cut on the framing steel which will go [...]

VW Bug MR2 Create rear frame templates from foam board #44

Posted on February 13th, 2009 by Tim in VW Beetle Turbo Build
Once the main frame rails are in place, I can now start building the VW Bug rear engine frame plates. I have constructed templates out of .25 inch foam board to determine their locations.

VW Bug - MR2 install main frame rails - bolt up torsion bars #43

Posted on February 12th, 2009 by Tim in VW Beetle Turbo Build
After creating the torsion bar mounts on the end of the VW Bug frame rails, I bolted up the Toyota MR2 torsion bars. I have also clamped the frame rails on the plywood template to be positioned between the front and rear suspension.

VW Bug - Toyota MR2 create torsion bar frame mounts #42

Posted on February 11th, 2009 by Tim in VW Beetle Turbo Build
Now that I know where the VW Bug main frame rails will be, I am creating the MR2 rear torque bar mounts in the end of the rail tubing.

VW Bug - Toyota MR2 create rear frame member template #41

Posted on February 10th, 2009 by Tim in VW Beetle Turbo Build
Creation of the VW Bug frame starts with determination of where and how the frame member will be positioned around the engine. I have very limited space around the Toyota MR2 3SGTE motor. My plan is to create a plate type frame that travels straight through the rear of the vehicle. I started with some [...]

VW Bug - Toyota MR2 Initial frame planning #40

Posted on February 9th, 2009 by Tim in VW Beetle Turbo Build
This video shows where the VW Bug main frame rails will terminate at the Toyota MR2 anti-torsion bars attached to the lower rear control arms.

VW Bug - Toyota MR2 Fit rear basket over the 3SGTE motor #39

Posted on February 6th, 2009 by Tim in VW Beetle Turbo Build
I am placing the basket material (constructed earlier) over the Toyota MR2 3SGTE motor. This gives me a good idea where everything will sit under the VW Bug body. I need this info to start the initial frame planning.

VW Bug - MR2 Final 3SGTE block up with mounts & accessories #38

Posted on February 5th, 2009 by Tim in VW Beetle Turbo Build
The initial frame plan can start, now that I have the VW Bug’s drive train in place. As you can see I have finished the alignment of the Toyota MR2 3SGTE motor. I have both struts in place as well as the motor mounts and all the accessories (starter and AC unit etc.). Oh and [...]

VW Bug - Toyota MR2 3SGTE rear cross-member and suspension #37

Posted on February 4th, 2009 by Tim in VW Beetle Turbo Build
I now have the MR2 3SGTE rear cross-member installed as well as tying in all the suspension components. The two lower control arms and the two rear control linkages attach to the cross-member. This is a tight fit under the VW Bug body.

VW Bug - Toyota MR2 drivetrain alignment and support #36

Posted on February 3rd, 2009 by Tim in VW Beetle Turbo Build
In this video you have to look for the changes. The engine is tilted back at the correct angle for the Toyota MR2 3SGTE engine. I also have blocks supporting the engine from below (no weight on the chains of the shop crane). I still need to install the rear cross-member to get everything exactly [...]

Archives

Full Archive

Featured Links

Tag Cloud